Master Clear™ Salt System Quick Start Guide
Congratulations on your saltwater hot tub. This step-by-step guide will walk you through the process of filling and balancing your water with the Master Clear™ Salt System, ensuring everything is ready for you to relax.
Before You Get Started
Make sure you have the following ready before beginning startup:
- Master Clear™ Salt System installed
- Master Clear startup supplies
- Salt Plus
- Test strips
- Spa drained and cleaned
- New standard spa filters (not EcoPur Charge filters)
Do Not Use
- Spa Hardness Up
- Pool chemicals
- Pool salt
Initial Saltwater System Start-Up
Fill Your Hot Tub
Install standard spa filters (not EcoPur Charge). Use a fill-water pre-filter where applicable. Fill the spa to the proper water level, then turn on the spa and prime all pumps before proceeding.
Add the Sequestering Agent
With the pumps running, add Metal Protect as directed. Allow the water to circulate and reach operating temperature before continuing.
Test the Water
Test the water and confirm it is within the manufacturer's recommended ranges before adding salt.
| Parameter | Target Range |
|---|---|
| pH | 7.0 – 7.2 |
| Total Alkalinity | 60 – 120 ppm |
Balance and Retest
Adjust pH and alkalinity as needed using appropriate spa chemicals. Allow the water to circulate before retesting. Confirm readings are within range before moving to the next step.
Add Salt Plus
Only add Salt Plus after the water is balanced and near operating temperature. Use the table below to determine the correct initial amount based on your spa's water volume.
| Spa Water Volume | Initial Salt Plus |
|---|---|
| 200 gal | 1⅝ cups |
| 250 gal | 2 cups |
| 300 gal | 2⅜ cups |
| 350 gal | 2¾ cups |
| 400 gal | 3⅛ cups |
| 450 gal | 3½ cups |
| 500 gal | 3⅞ cups |
| 550 gal | 4¼ cups |
Note: Do not add too much salt. Add gradually and recheck the system before adding more.
Connect to the Master Clear App
Download the Master Clear app and connect via Bluetooth to complete setup:
- Open the Master Clear app and enable Bluetooth on your phone.
- Follow the in-app prompts to pair with your spa's controller.
- Select your spa model and enter the fill volume when prompted.
- Confirm the connection and allow the system to initialize.
Check and Adjust Salt Levels
Use the app or controller to check the current salt reading. If additional salt is needed, add no more than one cup at a time, then allow the water to circulate for at least 15 minutes before rechecking.
Let the Spa Circulate
The manufacturer recommends allowing the system to run for several hours before first use. Use a test strip to verify sanitizer levels are within range before entering the spa.
Master Clear Maintenance Schedule
| Frequency | Tasks |
|---|---|
| Before Each Use | Test and verify sanitizer levels are within range. Rinse filters if needed. |
| After Heavy Use | Check sanitizer levels. Rinse filters if water appears cloudy or foamy. |
| Once a Week | Test and balance pH and alkalinity. Rinse filters. Check salt level via the app or controller. |
| Once a Month | Deep clean filters with filter cleaner. Inspect equipment and waterline for buildup. Wipe down spa shell. |
| Every 180 Days | Drain, clean, and refill the spa with fresh water. Repeat the full startup procedure. |
| Once a Year | Replace the Master Clear Smart Cell. Inspect all system components and connections. |
Water Care Troubleshooting
Select a symptom to see suggested steps.
A strong chlorine or chemical odor often indicates that sanitizer levels are too low, not too high. Test the water and adjust levels as needed.
General water odor may indicate insufficient sanitizer or unbalanced water chemistry. Test pH, alkalinity, and sanitizer levels and adjust accordingly.
Cloudy water is typically caused by unbalanced chemistry or a dirty filter. Check and balance pH and alkalinity, rinse the filters, and verify sanitizer levels.
Foam is usually caused by lotions, soaps, or body oils. Shower before soaking and use a spa defoamer if needed. If foam persists, a water change may be necessary.
Clean the waterline with a spa surface cleaner. Shower before each use to minimize oils and cosmetics entering the water.
Scale is typically calcium buildup. Maintain proper alkalinity and pH within recommended ranges and consider using a scale inhibitor.
Installing the Master Clear™ Salt System Activation Kit
Watch how to install the Master Clear™ Salt System Activation Kit.
